• Welcome to H4O! For a reduced ad experience, please login or register with the forum.

Svxr8dr's H3 build

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
I'm way late starting this but here goes.
Purchased 2008 Base model in late June 2017 with 54K miles on it. I had been looking on and off for a while after having been into Subaru's for many years. Needed a daily driver as weill as a vehicle that could take me up to the back country target shooting areas of which I travel to alot.
19488510_10155652331959406_176724798385494047_o.jpg
 
Last edited:

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
First mods were the simple and easy to get ones. center dash console, K&N drop in, and Weathertech floor mats:
console.jpgK&N.jpgWeathertech.jpg
 
Last edited:

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
No more chrome grill. Lamin-X Gunsmoke Fog Light Covers. Steelcraft Grill Guard. IPCW LEDC-346S Platinum Smoke front signal lamps. Finally leveled as well. Front bump stops replaced. EGR superguard bug shield/wind deflector, Skid plate front blacked out, Front passenger and drivers side windowss tinted to match the rest, and black PlastiDip on faux air intake covers.
23926336_10156106698584406_6765137872566262178_o.jpg
[FONT=&amp]https://imgur.com/9HL7PhR[/FONT]
 
Last edited:

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
Plastidip the wheels black. Purple Cranium Rear Diff Spider. Spyder Auto Black LED Tail Lights. Gobi ladder. Roc Doc spare tire bracket mount, FireStik K-1A Push-n-Twist quick disconnect, Firestik K4R Heavy-Duty Stud Mount, Firestik FS-4BK 4′ Ii Fs Series Tunable Tip Cb Antenna
wheels.jpg36176120_10156733856459406_4880434470169083904_o.jpg36575800_10156754173224406_7274726163270860800_o.jpg
 
Last edited:

Korby7

Well-Known Member
Messages
395
Location
Utah
Attachments don't seem to be working. I'd love to see all you've done.:thumbs:
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
Nerf bars gone. Replaced with GM oem rock sliders and GM OEM UCP (GM Part #12498474) w/Thor plates. Added STARR HID's.
36558214_10156754173439406_7950902561400160256_o.jpg
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
Air Doc, Supermodulation ported throttle body, and used a Hypertech setting all of my shift points to +200 and set the rev limiter to +500, plus adjusted the transmission firmness to 50%.
IMG_1007.JPG
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
Besides the Starr HID's and corners, I made other lighting changes:
License Plate - Pure White (5000K) HP5 (92 lumens)
Footwells - Cool White (6000K) HP5 (92 lumens)
Cargo Dome - Cool White (6000K) SMD12 Board (118 lumens)
Front Dome - Cool White (6000K) SMF4 (56 lumens)
Map Lights - Cool White (6000K) SMF4 (56 lumens)
Side Markers - Warm White HP3 (56 lumens)
Reverse LED Backup Lights - Cool White XP80 (520 lumens)
Rough Country - 70803BL - 2-inch Flush Mount Black Series CREE LED Square Lights
Rough Country - 70950BL - 50-inch Black Series Dual Row CREE LED Light Bar
GTR Lighting Ultra 2 Fog Lights LED (6000K and 1675 lumens)
XTR LP Reverse Light System
Reverse.JPGbar.JPG
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
Transmission cooler was added (Hayden 405). In retrospect I should have done a bar and plate rather than tube and fin. I may make that change down the road some.

Hayden405.JPG
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
Added accessories to the Gobi rack - storage box, ax&shovel attachment, hi-lift attachment, tie-down attachments and SXMA Fuel Tank Can (5 Gallon). I also added a PVC pipe to store my CB antennae when not in use.
BoraACC.JPG
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
The lift has delayed me going to 35's as I prefer to keep my vehicle garaged when home at night and my clearance is getting tight
clearance.JPG
 

svxr8dr

Well-Known Member
Messages
197
Location
SW WA ST
ViAir 450C air compressor, on Outfitter Design mount with a2.5g ViAir tank with front and rear quick connects. The front usually has a cap on it to prevent mud and debris from entering.
Mount.JPG
Compressor.JPG
frontQC.JPG
rearqc.JPG
 
Top