Welcome to the H4O - HUMMER 4x4 Off Road.
Results 1 to 7 of 7
  1. #1
    Super Swamper
    Join Date
    Jun 2015
    Location
    Way up north, UT
    Posts
    2,003
    Thanks
    534
    Thanked 579 Times in 399 Posts

    Hummer H3 fastener Torque specs

    I got tired of constantly digging up the fastener torque specs for my H3's so I just put together this list of all the fastener torque specifications i could find the the H3's. This was mainly pulled from the FSM's on Schwarttzy's site. Eventually I am going to make groups for the various common trail repairs we have to do to make it handier to look everything up. I'm printing out a copy to keep in my truck so that I always have it with me. I am pretty particular about tightening to spec rather than "good enough" since "good enough" often really isn't. That's how stuff either falls apart or breaks/leaks/makes noise/etc.

    Body:
    Check Link Bolt 25 N.m 18 lb ft
    Check Strap Nuts 9 N.m 80 lb in
    Endgate Assist Rod Stud 10 N.m 89 lb in
    Endgate Hinge Bolt 50 N.m 37 lb ft
    Fender Mount Bolts 10 N.m 89 lb in
    Front Side Door Hinge Bolts 25 N.m 18 lb ft
    Grille Support Bolts 9 N.m 27 lb in
    Hood Hinge Bolts 25 N.m 18 lb ft
    Hood Latch Release Screws 2 N.m 18 lb in
    Hood Latch Screws 10 N.m 89 lb in
    Rear Side Door Hinge Bolts 25 N.m 18 lb ft

    Brush Guard Bolts - Lower Short Bolts 50 N.m 37 lb ft
    Brush Guard Bolts - Upper Long Bolts 85 N.m 63 lb ft
    Brush Guard Nuts 50 N.m 37 lb ft
    Front Bumper Bolts 40 N.m 30 lb ft
    Front Bumper Lower Bolts 50 N.m 37 lb ft
    Front Bumper Upper Bolts 85 N.m 63 lb ft
    Rear Bumper Bolts 32 N.m 24 lb ft
    Rear Bumper Bracket to Bumper End Cap Nut 32 N.m 24 lb ft
    Rear Bumper Bracket to Frame Bolts 85 N.m 63 lb ft
    Rear Bumper Bracket to Trailer Hitch Nut 85 N.m 63 lb ft
    Rear Bumper End Cap Nuts to Bumper 32 N.m 24 lb ft
    Trailer Hitch Electrical Receptacle to Rear Bumper Bolts 32 N.m 24 lb ft
    Trailer Hitch to Frame Bolts 100 N.m 74 lb ft

    Cargo Tie Down Loops 34 N.m 25 lb ft
    Front Bumper Impact Bar Bolts 50 N.m 37 lb ft
    Grille Guard/Brush Guard Bolts 50 N.m 37 lb ft
    Radiator Grille Nut 3 N.m 27 lb in
    Rear Side Door Flare Screws 2 N.m 18 lb in
    Rear Wheel Opening Flare Bolts 9 N.m 80 lb in
    Rocker Panel Screws 2 N.m 18 lb in
    Windshield Side Reveal Molding Screws 2 N.m 18 lb in

    Front Side Door Mirror Bolts 10 N.m 89 lb in
    Rearview Mirror Screw 2 N.m 18 lb in

    Wipers:

    Front Wiper Arm Shaft Nut 21 N.m 15 lb ft
    Front Wiper Motor Bolts 12 N.m 9 lb ft
    Rear Wiper Arm Nut 9 N.m 80 lb in
    Rear Wiper Motor Bolts 10 N.m 89 lb in
    Washer Solvent Reservoir Nuts 10 N.m 89 lb in
    Wiper Motor Transmission Bolts 10 N.m 89 lb in


    Interior:

    Sunshade Bolt 2 N.m 18 lb in
    Rear Side Door Armrest Bracket Bolt 10 N.m 89 lb in
    C Pillar Assist Handle Bolt 52 N.m 38 lb ft
    Assist Handle Bolt 9 N.m 80 lb in
    Rear Seat Cup Holder Screw 2 N.m 18 lb in
    Upper Body Side Garnish Screw 2 N.m 18 lb in
    Windshield Side Garnish Screw 9 N.m 80 lb in
    Door Trim Panel Screw 2 N.m 18 lb in
    Door Trim Panel Bolt 9 N.m 80 lb in
    Sunshade Screw 2 N.m 18 lb in
    Front Seat Switch Screw 2 N.m 18 lb in

    Frame:

    Assist Step Bolt 50 N.m 37 lb ft
    Crossmember Bolt
    First Pass 70 N.m 52 lb ft
    Second Pass Plus 200 Degrees
    Engine Shield Bolt 20 N.m 15 lb ft
    Frame Cushion/Insulator Bolt 115 N.m 85 lb ft
    Front Differential Assembly Bolt 100 N.m 74 lb ft
    Oil Pan Skid Plate Bolt 20 N.m 15 lb ft
    Tow Hook Bracket to Front Frame Rail Bolt 85 N.m 63 lb ft
    Tow Hook Bracket to Rear Frame Rail Bolt 100 N.m 74 lb ft
    Tow Hook D-Ring Nut First Pass 50 N.m 37 lb ft
    Second Pass Minus Approximately 180 Degrees
    Trailer Hitch to Frame (Horizontal) Bolt 160 N.m 118 lb ft
    Trailer Hitch to Frame (Vertical) Bolt 100 N.m 74 lb ft
    Transmission Crossmember to Frame (Vertical) Bolt 100 N.m 74 lb ft
    Transmission Crossmember to Frame Bracket (Horizontal) Nut 50 N.m 37 lb ft
    Transmission Mount to Support Nut 57 N.m 42 lb ft
    Wheelhouse Panel Bolts 10 N.m 89 lb in

    Exhaust:

    Catalytic Converter Heat Shield 9 N.m 80 lb in
    Catalytic Converter Nut 50 N.m 37 lb ft
    Exhaust Manifold Bolt
    First Pass 20 N.m 15 lb ft
    Second Pass 20 N.m 15 lb ft
    Final Pass 20 N.m 15 lb ft
    Exhaust Manifold Heat Shield Nut 10 N.m 89 lb in
    Exhaust Muffler Heat Shield 9 N.m 80 lb in
    Exhaust Pipe Heat Shield 9 N.m 80 lb in
    Leaf Spring Bolt and Nut 85 N.m 63 lb ft
    Lower Shock Absorber Bolt and Nut 95 N.m 70 lb ft
    Muffler Nut 45 N.m 33 lb ft
    Transmission Filler Tube Bracket Nut 12.5 N.m 111 lb in

    Cooling System:

    Coolant Heater 50 N.m 37 lb ft
    Coolant Recovery Reservoir Bolt 10 N.m 89 lb in
    Fan Blade Bolt 27 N.m 20 lb ft
    Fan Clutch Nut 56 N.m 41 lb ft
    Thermostat Housing Bolt 10 N.m 89 lb in
    Water Outlet Housing Bolt 10 N.m 89 lb in
    Water Pump Bolt 10 N.m 89 lb in
    Water Pump Pulley Bolt 25 N.m 18 lb ft
    Last edited by JPaul; 02-02-2020 at 04:47 PM.
    2008 H3 Alpha

    "Live free or die: Death is not the worst of evils." - General John Stark

    N1JPA

  2. The Following 4 Users Say Thank You to JPaul For This Useful Post:

    cgalpha08 (02-02-2020), EndeavoredH3 (02-02-2020), scoreh3 (02-02-2020), Sennin (02-03-2020)

  3. #2
    Super Swamper
    Join Date
    Jun 2015
    Location
    Way up north, UT
    Posts
    2,003
    Thanks
    534
    Thanked 579 Times in 399 Posts
    Drivetrain:

    Differential Carrier Assembly Bearing Cap Bolts 63 N.m 46 lb ft
    Differential Carrier Assembly Mounting Bracket to Carrier Bolts 155 N.m 114 lb ft
    Differential Carrier Assembly Mounting Bracket to Frame Bolts 155 N.m 114 lb ft
    Differential Housing Cover Bolts 30 N.m 22 lb ft
    Intermediate Shaft Housing Assembly to Axle Housing Bolts 67 N.m 49 lb ft
    Intermediate Shaft Housing to Outer Housing Bolts 48 N.m 35 lb ft
    Pinion Shaft Lock Screw/Bolt 25 N.m 18 lb ft
    Plug, Drain and Fill 32 N.m 24 lb ft
    Ring Gear Bolts 120 N.m 89 lb ft
    Third Point Mount Bolt 110 N.m 81 lb ft
    Bolt - Front Propeller Shaft CV Joint to Transfer Case Drive Flange (4) 61 N.m 45 lb ft
    Bolt - Front Propeller Shaft to Front Pinion Yoke (4) 25 N.m 18 lb ft
    Bolt - Rear Propeller Shaft Retainer (8) 25 N.m 18 lb ft

    Bearing Cap Bolt 75 N.m 55 lb ft
    Brake Line Retainer Bolt 20 N.m 15 lb ft
    Differential Housing Cover Bolt 25 N.m 18 lb ft
    Disc Brake Backing Plate Bolt 135 N.m 100 lb ft
    Fill/Drain Plug 33 N.m 24 lb ft
    Park Brake Cable to Leaf Spring Bolt 20 N.m 18 lb ft
    Pinion Shaft Lock Bolt 25 N.m 18 lb ft
    Ring Gear Bolt 120 N.m 89 lb ft
    Wheel Speed Sensor Bolt 18 N.m 13 lb ft

    Front Wheel Drive Shaft Nut 260 N.m 191 lb ft

    Transmission:

    pressure plug 8-14 N.m (6-10 lb ft)
    transmission range selector cable bracket bolts to 25 N.m (18 lb ft)
    Floor Shift Control Bolts 20 N.m (15 lb ft)
    park/neutral back up switch bolts 27 N.m (20 lb ft)
    control lever nut 20 N.m (15 lb ft)
    oil pan to transmission case bolts 16 N.m (12 lb ft)
    manual detent spring bolt 31 N.m (23 lb ft)
    Transmission Mount Bolt 50 N.m (37 lb ft)
    torque converter bolts 60 N.m 44 lb ft)
    fuel hose/pipe bracket nuts 20 N.m (15 lb ft)
    Cooler connector 38 N.m (28 lb ft)
    parking lock bracket bolt 31 N.m (23 lb ft)
    pump cover bolts 24 N.m (18 lb ft)
    pump to case bolts 29 N.m (21 lb ft)
    converter housing bolts 65-75 N.m (48-55 lb ft)
    solenoid retainer bolt 8-14 N.m (6-10 lb ft)
    accumulator bolt 11 N.m (8.11 lb ft)
    torque converter clutch (TCC) solenoid valve bolts 8-14 N.m (6-10 lb ft)
    valve body bolts 8-14 N.m (6-10 lb ft)

    Transfer Case:

    Adapter Studs 14 N.m 10 lb ft
    Case Bolts 25 N.m 18 lb ft
    Drain Plug 16 N.m 12 lb ft
    Encoder Motor Bolts 10 N.m 89 lb in
    Encoder Motor Bracket Bolt 10 N.m 89 lb in
    Encoder Motor Support Bracket Nuts 5 N.m 44 lb in
    Fill Plug 16 N.m 12 lb ft
    Front Drive Shaft Universal Joint Clamp Bolts 20 N.m 15 lb ft
    Front Output Shaft Flange Nut 319 N.m 235 lb ft
    Transfer Case Shield Bolts 30 N.m 23 lb ft
    Transfer Case to Transmission Nuts 50 N.m 37 lb ft
    Transmission Crossmember to Frame Bracket - Horizontal - Bolts and Nuts 50 N.m 37 lb ft
    Transmission Crossmember to Frame - Vertical -Bolts 100 N.m 74 lb ft
    Transmission Mount to Support Nuts 57 N.m 42 lb ft
    Vehicle Speed Sensor 17 N.m 13 lb ft
    Vent 6 N.m 53 lb in

    Brakes:

    Backing Plate Bolts 135 N.m 100 lb ft
    Brake Hose to Caliper Bolt, Front 40 N.m 30 lb ft
    Brake Hose to Caliper Bolt, Rear 40 N.m 30 lb ft
    Front Brake Caliper Mounting Bolt 195 N.m 144 lb ft
    Park Brake Equalizer 3.5 N.m 31 lb in
    Quarter Shaft Shield 25 N.m 18 lb ft
    Rear Brake Caliper Guide Pin Bolt 36 N.m 27 lb ft
    Rear Brake Caliper Mounting Bolt 135 N.m 100 lb ft
    Rear Brake Caliper Mounting Bracket Bolt 135 N.m 100 lb ft

    BPMV Module Mounting Bolts 32 N.m 24 lb ft
    Brake Fluid Level Sensor Harness Bracket Bolt 8 N.m 71 lb ft
    Brake Pipe Fittings 19 N.m 14 lb ft
    Longitudinal Accelerometer Nut 9 N.m 80 lb in
    Master Cylinder Nuts 30 N.m 22 lb ft
    Wheel Speed Sensor Harness Clip Bolt 9 N.m 80 lb in
    Wheel Speed Sensor Mounting Bolt 18 N.m 13 lb ft

    Brake Hose to Caliper Bolt, Front 40 N.m 30 lb ft
    Brake Hose to Caliper Bolt, Rear 40 N.m 30 lb ft
    Brake Pedal Bolt 27 N.m 20 lb ft
    Brake Pipe Fittings 19 N.m 14 lb ft
    Brake Pipe Fittings, Power Brake Booster Outlet Front Pipe 15 N.m 11 lb ft
    Front Brake Caliper Bleed Screw 11 N.m 97 lb in
    Front Brake Hose Bracket Bolt 9 N.m 80 lb in
    Hose Bracket to Anchor Plate Bolt 25 N.m 18 lb ft
    Hose Bracket to Frame Bolt 12 N.m 106 lb in
    Hose Bracket to Knuckle Bolt 12 N.m 106 lb in
    Hose Bracket to Rear Axle Bolt 22 N.m 16 lb ft
    Hose Bracket to Steering Knuckle 9 N.m 80 lb in
    Hose Bracket to Upper Control Arm Bolt 9 N.m 80 lb in
    Master Cylinder Mounting Nuts 30 N.m 22 lb ft
    Master Cylinder Reservoir Bolt 2 N.m 18 lb in
    Power Brake Booster Pump Bolts 8 N.m 71 lb in
    Power Brake Booster Pump Motor Wire Retaining Screws 3 N.m 27 lb in
    Rear Brake Caliper Bleed Screw 10 N.m 89 lb in
    Rear Brake Hose Bracket to Jounce Bumper Bolt 9 N.m 80 lb in
    Rear Brake Hose to Frame Bolt 2 N.m 17 lb in

    Parking Brake:

    Front Park Brake Cable Bracket Bolt 20 N.m 15 lb ft
    Front Park Brake Cable Cowl Bolt (RHD) 20 N.m 15 lb ft
    Front Park Brake Cable Lower Bolt (RHD) 20 N.m 15 lb ft
    Park Brake Cable Bracket Nut 48 N.m 35 lb ft
    Park Brake Cable Clip Bolt 25 N.m 18 lb ft
    Park Brake Lever Lower Bracket Nut (RHD) 20 N.m 15 lb ft
    Park Brake Lever Side Bracket Bolt (RHD) 20 N.m 15 lb ft
    Park Brake Lever Upper Bracket Bolt (RHD) 20 N.m 15 lb ft
    Park Brake Lever Upper Nut (RHD) 20 N.m 15 lb ft
    Park Brake Pedal Bolt 20 N.m 15 lb ft
    Park Brake Pedal Nut 20 N.m 15 lb ft
    Park Brake Warning Lamp Switch Bolt 3 N.m 25 lb in

    Front Suspension:

    Hub and Bearing Assembly to Steering Knuckle Bolts 180 N.m 133 lb ft
    Lower Control Arm Ball Joint Stud Nut First Pass 85 N.m 63 lb ft
    Second Pass Plus 60 Degrees
    Lower Control Arm to Frame Bolts Front 165 N.m 122 lb ft
    Lower Control Arm to Frame Bolts Rear 180 N.m 133 lb ft
    Shock Absorber Tenon Nut 30 N.m 22 lb ft
    Shock Absorber to Lower Control Arm Nut 80 N.m 59 lb ft
    Stabilizer Shaft Insulator Clamp Bolts 50 N.m 37 lb ft
    Stabilizer Shaft Link Nuts 80 N.m 59 lb ft
    Upper Control Arm Ball Pinch Bolt Nut 70 N.m 51 lb ft
    Upper Control Arm to Frame Nuts 155 N.m 114 lb ft
    Wheel Speed Sensor Mounting Bracket Bolt 20 N.m 15 lb ft

    Rear Suspension:

    Leaf Spring to Front Bracket Nut 125 N.m 92 lb ft
    Leaf Spring U-Bolt Nuts 76 N.m 56 lb ft
    Spring Shackle to Frame Nut 85 N.m 63 lb ft
    Spring Shackle to Leaf Spring Nut 85 N.m 63 lb ft
    Shock Absorber Lower Bolt 95 N.m 70 lb ft
    Shock Absorber Upper Bolts 35 N.m 26 lb ft
    Stabilizer Bar Lower Link Nut 80 N.m 59 lb ft
    Stabilizer Bar Upper Link to Frame Nut 80 N.m 59 lb ft
    Stabilizer Clamp Bolts 50 N.m 37 lb ft

    Power Steering:

    Power Steering Gear Inlet and Outlet Hose Retaining Plate Bolt 12 N.m 106 lb in
    Power Steering Gear Inlet and Outlet Hose Bracket Bolt 9 N.m 80 lb in
    Power Steering Gear Inlet Hose Fitting 25 N.m 18 lb ft
    Power Steering Pump Bolt 25 N.m 18 lb ft
    Power Steering Pump Bracket Bolt 50 N.m 37 lb ft
    Rack and Pinion Inner Tie Rod 88 N.m 65 lb ft
    Rack and Pinion Outer Tie Rod End Nut 71 N.m 52 lb ft
    Steering Gear Bolt 130 N.m 96 lb ft
    Steering Gear Bracket Bolt 100 N.m 74 lb ft

    Lower Intermediate Steering Shaft Bolt 45 N.m 33 lb ft
    Lower Steering Column Trim Cover Bolt 3.5 N.m 31 lb in
    Multifunction Turn Signal Switch Housing Bolt 2.5 N.m 22 lb in
    Steering Column Bolt 25 N.m 18 lb ft
    Steering Column Nut 30 N.m 22 lb ft
    Steering Wheel Nut 35 N.m 26 lb ft
    Tilt Lever Bolt 1 N.m 9 lb in
    Turn Signal Multifunction Switch Bolt 4.5 N.m 40 lb in
    Upper Intermediate Steering Shaft Bolt (at the lower intermediate steering shaft) 23 N.m 17 lb ft
    Upper Intermediate Steering Shaft Bolt (at thesteering gear) 62 N.m 46 lb ft
    2008 H3 Alpha

    "Live free or die: Death is not the worst of evils." - General John Stark

    N1JPA

  4. The Following 4 Users Say Thank You to JPaul For This Useful Post:

    cgalpha08 (02-02-2020), EndeavoredH3 (02-02-2020), scoreh3 (02-02-2020), Sennin (02-03-2020)

  5. #3
    Super Swamper
    Join Date
    Jun 2015
    Location
    Way up north, UT
    Posts
    2,003
    Thanks
    534
    Thanked 579 Times in 399 Posts
    3.7 Engine:

    A/C Compressor Hose/Pipe Bracket Bolt 9 N.m 80 lb in
    A.I.R. Cover Stud 25 N.m 18 lb ft
    Balance Shaft Retaining Bolt 10 N.m 89 lb in
    Balance Shaft Chain Guide Bolt 10 N.m 89 lb in
    Balance Shaft Chain Tensioner Bolt 10 N.m 89 lb in
    Battery Negative Cable to Engine Block Bolt 35 N.m 26 lb in
    Battery Positive Cable to Starter Terminal Nut 9 N.m 80 lb in
    Camshaft Cap Bolt 12 N.m 106 lb in
    Camshaft Cover Bolt 10 N.m 89 lb in
    Camshaft Position Actuator Valve Bolt 10 N.m 89 lb in
    Connecting Rod Cap Bolt First Pass 25 N.m 18 lb ft
    Final Pass 110 degrees
    Coolant Temperature Sensor 16 N.m 12 lb ft
    Crankshaft Balancer Bolt
    First Pass 150 N.m 110 lb ft
    Final Pass 180 degrees
    Crankshaft Main Bearing Cap Bolt
    First Pass 25 N.m 18 lb ft
    Final Pass 180 degrees
    Crankshaft Position Sensor Bolt 10 N.m 89 lb in
    Crankshaft Rear Oil Seal Housing Bolt 10 N.m 89 lb in
    Cylinder Head Access Hole Plug - Plastic 5 N.m 44 lb in
    Cylinder Head Bolt - 12
    First Pass 30 N.m 22 lb ft
    Final Pass 155 degrees
    Cylinder Head End Bolts - 2 Short
    First Pass 7 N.m 62 lb in
    Final Pass 60 degrees
    Cylinder Head End Bolts - 1 Long
    First Pass 7 N.m 62 lb in
    Final Pass 120 degrees
    Cylinder Head Oil Gallery Plug 38 N.m 28 lb ft
    Differential Carrier Assembly Bushing to Frame Bolt 152 N.m 112 lb ft
    Drive Belt Idler Pulley Bolt 50 N.m 37 lb ft
    Drive Belt Tensioner Bolt 50 N.m 37 lb ft
    Engine Block Coolant Plug 50 N.m 37 lb ft
    Engine Block Oil Gallery Plug - Side 35 N.m 26 lb ft
    Engine Flywheel Bolt
    First Pass 40 N.m 30 lb ft
    Final Pass 45 degrees
    Engine Front Cover Bolt 10 N.m 89 lb in
    Engine Front Cover - Center - Small Bolt 8 N.m 71 lb in
    Engine Front Cover Spacer Bolt 10 N.m 89 lb in
    Engine Front Lift Bracket Bolt
    First Pass 5 N.m 44 lb in
    Final Pass 50 N.m 37 lb ft
    Engine Mount Bolt 50 N.m 37 lb ft
    Engine Mount-to-Frame Bracket Bolt 85 N.m 63 lb ft
    Engine Wiring Ground Lead Bolt 20 N.m 15 lb ft
    Engine Wiring Harness Bracket Bolt 10 N.m 89 lb ft
    EVAP Purge Solenoid Valve Bolt 10 N.m 89 lb in
    Exhaust Camshaft Actuator Bolt
    First Pass 25 N.m 18 lb ft
    Final Pass 135 degrees
    Exhaust Camshaft Position Sensor Bolt 10 N.m 89 lb in
    Exhaust Manifold Bolt
    First Pass 20 N.m 15 lb ft
    Second Pass 20 N.m 15 lb ft
    Final Pass 20 N.m 15 lb ft
    Exhaust Manifold Heat Shield Nut 10 N.m 89 lb in
    Exhaust Manifold Heat Shield Stud 10 N.m 89 lb in
    Fuel Hose/Pipe Bracket Nut 20 N.m 15 lb ft
    Fuel Injector Rail Bolt 10 N.m 89 lb in
    Fuel Pressure Regulator Bolt 8 N.m 70 lb in
    Generator Mounting Bolt 50 N.m 37 lb in
    Heater Inlet Pipe Bolt 10 N.m 89 lb in
    Heater Outlet Fitting 45 N.m 33 lb ft
    Ignition Control Module Bolt 10 N.m 89 lb in
    Heater Outlet Hose/Pipe Bracket to Left Engine Mount Bolt 9 N.m 80 lb in
    Intake Camshaft Position Sensor Bolt 10 N.m 89 lb in
    Intake Camshaft Sprocket Bolt
    First Pass 20 N.m 15 lb ft
    Final Pass 100 degrees
    Intake Manifold Bolt 10 N.m 89 lb in
    Knock Sensor 25 N.m 18 lb ft
    Oil Filter 30 N.m 22 lb ft
    Oil Filter Adapter 50 N.m 37 lb ft
    Oil Filter Bypass Hole Plug 14 N.m 124 lb in
    Oil Level Indicator Tube Bolt 10 N.m 89 lb in
    Oil Pan Bolt - Ends 10 N.m 89 lb in
    Oil Pan Bolt - Sides 25 N.m 18 lb ft
    Oil Pan Drain Plug 26 N.m 19 lb ft
    Oil Pressure Switch 20 N.m 15 lb ft
    Oil Pump Cover Bolt 10 N.m 89 lb in
    Oil Pump Pipe and Screen Assembly Bolt 10 N.m 89 lb in
    Oil Pump Pressure Relief Valve Plug 14 N.m 124 lb in
    Power Steering Pump Bolt 25 N.m 18 lb ft
    Power Steering Pump Bracket Bolt 50 N.m 37 lb ft
    Spark Plug 18 N.m 13 lb ft
    Starter Motor Bolt 50 N.m 37 lb ft
    Starter Motor Nut 50 N.m 37 lb ft
    Starter Motor Stud 16 N.m 12 lb ft
    Starter Solenoid - S Terminal Nut 3.5 N.m 31 lb in
    Thermostat Housing bolt 10 N.m 89 lb in
    Throttle Control Module Bolt 10 N.m 89 lb in
    Timing Chain Tensioner Bolt 25 N.m 18 lb ft
    Timing Chain Tensioner Guide Bolt 22 N.m 16 lb ft
    Timing Chain Tensioner Shoe Bolt 25 N.m 18 lb ft
    Torque Converter Bolts 60 N.m 44 lb ft
    Transmission Mounting Bolts 50 N.m 37 lb ft
    Transmission Oil Cooler Pipes Bracket Bolt 20 N.m 15 lb ft
    Water Outlet Bolt 10 N.m 89 lb in
    Water Pump Bolt 10 N.m 89 lb in
    Water Pump Pulley Bolt 25 N.m 18 lb ft
    2008 H3 Alpha

    "Live free or die: Death is not the worst of evils." - General John Stark

    N1JPA

  6. The Following 4 Users Say Thank You to JPaul For This Useful Post:

    cgalpha08 (02-02-2020), EndeavoredH3 (02-02-2020), scoreh3 (02-02-2020), Sennin (02-03-2020)

  7. #4
    Super Swamper
    Join Date
    Jun 2015
    Location
    Way up north, UT
    Posts
    2,003
    Thanks
    534
    Thanked 579 Times in 399 Posts
    5.3 Engine:

    Accessory Drive Belt Idler Pulley Bolt 50 N.m 37 lb ft
    Accessory Drive Belt Tensioner Bolts 50 N.m 37 lb ft
    Automatic Transmission Flex Plate Bolts - First Pass 20 N.m 15 lb ft
    Automatic Transmission Flex Plate Bolts - Second Pass 50 N.m 37 lb ft
    Automatic Transmission Flex Plate Bolts - Final Pass 100 N.m 74 lb ft
    Battery Cable Channel Bolt 12 N.m 106 lb in
    Camshaft Position (CMP) Sensor Bolt 12 N.m 106 lb in
    Camshaft Position (CMP) Sensor Wire Harness Bolt 12 N.m 106 lb in
    Camshaft Retainer Bolts - Hex Head Bolts 25 N.m 18 lb ft
    Camshaft Retainer Bolts - TORX Head Bolts 15 N.m 11 lb ft
    Camshaft Sprocket Bolt - First Pass 75 N.m 55 lb ft
    Camshaft Sprocket Bolt - Final Pass 50 degrees
    Connecting Rod Bolts - First Pass 20 N.m 15 lb ft
    Connecting Rod Bolts - Final Pass 85 degrees
    Coolant Air Bleed Pipe and Cover Bolts 12 N.m 106 lb in
    Coolant Temperature Sensor 20 N.m 15 lb ft
    Crankshaft Balancer Bolt - Installation Pass - to Ensure the Balancer is Completely Installed 330 N.m 240 lb ft
    Crankshaft Balancer Bolt - First Pass - Install a NEW Bolt After the Installation Pass and Tighten as Described in the First and Final Passes 50 N.m 37 lb ft
    Crankshaft Balancer Bolt - Final Pass 140 degrees
    Crankshaft Bearing Cap M8 Bolts 25 N.m 18 lb ft
    Crankshaft Bearing Cap M10 Bolts - First Pass in Sequence 20 N.m 15 lb ft
    Crankshaft Bearing Cap M10 Bolts - Final Pass in Sequence 80 degrees
    Crankshaft Bearing Cap M10 Studs - First Pass in Sequence 20 N.m 15 lb ft
    Crankshaft Bearing Cap M10 Studs - Final Pass in Sequence 51 degrees
    Crankshaft Oil Deflector Nuts 25 N.m 18 lb ft
    Crankshaft Position (CKP) Sensor Bolt 25 N.m 18 lb ft
    Crankshaft Rear Oil Seal Housing Bolts 30 N.m 22 lb ft
    Cylinder Head M8 Bolts - in Sequence 30 N.m 22 lb ft
    Cylinder Head M11 Bolts - First Pass in Sequence 30 N.m 22 lb ft
    Cylinder Head M11 Bolts - Second Pass in Sequence 90 degrees
    Cylinder Head M11 Bolts - Final Pass in Sequence 70 degrees
    Cylinder Head Plug 20 N.m 15 lb ft
    Engine Block Coolant Drain Hole Plug 60 N.m 44 lb ft
    Engine Block Coolant Heater 50 N.m 37 lb ft
    Engine Block Oil Gallery Plugs 60 N.m 44 lb ft
    Engine Harness Ground Strap Bolt/Stud 16 N.m 12 lb ft
    Engine Harness-to-Generator Bracket Bolt 9 N.m 80 lb in
    Engine Harness Retainer-to-Intake Manifold Nut 5 N.m 44 lb in
    Engine Mount Bracket Through Bolt 100 N.m 74 lb ft
    Engine Mount-to-Engine Block Bolts 55 N.m 41 lb ft
    Evaporative (EVAP) Emission Pipe Bracket Nut 20 N.m 15 lb ft
    Exhaust Manifold Bolts - First Pass 15 N.m 11 lb ft
    Exhaust Manifold Bolts - Final Pass 20 N.m 15 lb ft
    Exhaust Manifold Heat Shield Bolts 9 N.m 80 lb in
    Exhaust Manifold Studs 20 N.m 15 lb ft
    Front Cover Bolts 25 N.m 18 lb ft
    Fuel Injection Fuel Rail Bolts 10 N.m 89 lb in
    Fuel Injection Fuel Rail Crossover Tube Bolts 3.8 N.m 34 lb in
    Fuel Rail Stop Bracket Bolt 50 N.m 37 lb ft
    Generator Bracket Bolts 50 N.m 37 lb ft
    Ignition Coil Bracket-to-Valve Rocker Arm Cover Studs 12 N.m 106 lb in
    Ignition Coil-to-Bracket Bolts 10 N.m 89 lb in
    Intake Manifold Bolts - First Pass in Sequence 5 N.m 44 lb in
    Intake Manifold Bolts - Final Pass in Sequence 10 N.m 89 lb in
    Intake Manifold Sight Shield Retainer Bolts 5 N.m 44 lb in
    J 41798 M8 Bolt 25 N.m 18 lb ft
    J 41798 M10 Bolts 50 N.m 37 lb ft
    Knock Sensor Bolts 25 N.m 18 lb ft
    Negative Battery Cable Stud 25 N.m 18 lb ft
    Oil Filter 30 N.m 22 lb ft
    Oil Filter Fitting 55 N.m 40 lb ft
    Oil Level Indicator Switch 20 N.m 15 lb ft
    Oil Level Indicator Tube Bolt 25 N.m 18 lb ft
    Oil Pan Baffle Bolts 9 N.m 80 lb in
    Oil Pan Closeout Cover Bolt - Left Side 9 N.m 80 lb in
    Oil Pan Closeout Cover Bolt - Right Side 9 N.m 80 lb in
    Oil Pan Cover Bolts 9 N.m 80 lb in
    Oil Pan Drain Plug 25 N.m 18 lb ft
    Oil Pan M6 Bolts - Oil Pan-to-Rear Housing 12 N.m 106 lb in
    Oil Pan M8 Bolts - Oil Pan-to-Engine Block and Oil Pan-to-Front Cover 25 N.m 18 lb ft
    Oil Pressure Relief Valve 27 N.m 20 lb ft
    Oil Pressure Sensor 35 N.m 26 lb ft
    Oil Pump Cover Bolts 12 N.m 106 lb in
    Oil Pump Relief Valve Plug 12 N.m 106 lb in
    Oil Pump Screen Nuts 25 N.m 18 lb ft
    Oil Pump Screen-to-Oil Pump Bolts 12 N.m 106 lb in
    Oil Pump-to-Engine Block Bolts 25 N.m 18 lb ft
    Power Steering Pump-to-Engine Block Bolts 50 N.m 37 lb ft
    Spark Plugs 15 N.m 11 lb ft
    Throttle Body Bolts 10 N.m 89 lb in
    Throttle Body Nuts 10 N.m 89 lb in
    Throttle Body Studs 6 N.m 53 lb in
    Timing Chain Tensioner Bolts 25 N.m 18 lb ft
    Valley Cover Bolts 25 N.m 18 lb ft
    Valve Lifter Guide Bolts 12 N.m 106 lb in
    Valve Rocker Arm Bolts 30 N.m 22 lb ft
    Valve Rocker Arm Cover Bolts 12 N.m 106 lb in
    Water Inlet Housing Bolts 15 N.m 11 lb ft
    Water Pump Bolts - First Pass 15 N.m 11 lb ft
    Water Pump Bolts - Final Pass 30 N.m 22 lb ft
    2008 H3 Alpha

    "Live free or die: Death is not the worst of evils." - General John Stark

    N1JPA

  8. The Following 7 Users Say Thank You to JPaul For This Useful Post:

    Bowser-II (02-02-2020), cgalpha08 (02-02-2020), EndeavoredH3 (02-02-2020), jphh20 (02-02-2020), Korby7 (02-02-2020), scoreh3 (02-02-2020), Sennin (02-03-2020)

  9. #5
    Low Profile
    Join Date
    Nov 2015
    Location
    Hagerstown, Maryland
    Posts
    195
    Thanks
    87
    Thanked 48 Times in 38 Posts
    I started a similar thing using MS OneNote about two years ago for each vehicle, but this is way more comprehensive!

    Very nice


    Sent from my iPhone using Tapatalk

  10. #6
    Mud Terrain
    Join Date
    Aug 2012
    Location
    SoCal
    Posts
    889
    Thanks
    178
    Thanked 143 Times in 125 Posts
    I cut and pasted them in the notes section of my phone. Thanks now I don’t have to keep looking them up online. Very helpful!

  11. #7
    Low Profile
    Join Date
    Jan 2018
    Location
    Arizona
    Posts
    136
    Thanks
    47
    Thanked 37 Times in 28 Posts
    Just hopped off my phone to log onto the computer to give thanks . Very invaluable, thanks for taking the time.


    "Just Hit It With Your Purse"


 

Similar Threads

  1. Replies: 1
    Last Post: 10-28-2019, 12:17 AM
  2. Fastener On Jack Door is Busted
    By K0PIR in forum HUMMER H3 2006-2010; H3T 2009-2010
    Replies: 5
    Last Post: 02-16-2015, 09:01 PM
  3. Alignment specs after leveling?
    By rsm688 in forum HUMMER H3 2006-2010; H3T 2009-2010
    Replies: 16
    Last Post: 11-13-2014, 11:25 PM
  4. torque specs
    By digglesworth in forum HUMMER H3 2006-2010; H3T 2009-2010
    Replies: 5
    Last Post: 10-26-2013, 01:07 PM
  5. Alignment specs after leveling
    By Pappibri in forum HUMMER H3 2006-2010; H3T 2009-2010
    Replies: 16
    Last Post: 05-08-2013, 08:49 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Logout