Welcome to the H4O - HUMMER 4x4 Off Road.

Search:

Type: Posts; User: JPaul

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    35
    Views
    1,122

    Very nice! Steve's trailer needs a nameplate...

    Very nice!

    Steve's trailer needs a nameplate attached to it designating it the official H4O Hummer Hauler. Same with Alex's truck! Maybe a full body wrap. :giggle:
  2. Some things to check:...

    Some things to check: https://www.obd-codes.com/p0523

    This one talks about the filter screen they had in some years, not sure if the H3 had them or not. I know mine didn't....
  3. Replies
    16
    Views
    3,085

    Pics of the handles? I'm interested, my daughters...

    Pics of the handles? I'm interested, my daughters have almost succeeded in yanking off one of the rear ones.

    Sent from my SM-N950U using Tapatalk
  4. Replies
    12
    Views
    234

    Jeepwalker, the only guy I know that has longer...

    Jeepwalker, the only guy I know that has longer posts on average than myself. [emoji38]

    Sent from my SM-N950U using Tapatalk
  5. Replies
    12
    Views
    234

    What's so hard about the speed sensors on either...

    What's so hard about the speed sensors on either axle? The rear's are right there on the back of the axle, just one 10mm bolt and they're out, just have to unhook the strain relief in the wheel well...
  6. Replies
    9
    Views
    219

    That is a surprisingly clean 06. Seems like it...

    That is a surprisingly clean 06. Seems like it was garaged it's whole life, the a-pillar trim still looks new, it's not even totally warped at the top like it usually gets. Nice find.
  7. Thread: Storage Advice

    by JPaul
    Replies
    5
    Views
    148

    The plastic ammo crates from MTM are really nice,...

    The plastic ammo crates from MTM are really nice, and cheap too. I use a couple of the smaller ones and medium ones for storing my offroading gear:

    Small ($15 currently)...
  8. Replies
    12
    Views
    234

    Very probable. Replace them and see if it goes...

    Very probable. Replace them and see if it goes away (since they apparently need to be replaced regardless).
  9. H3 the gauge is just a suggestion as to how hot the...

    the gauge is just a suggestion as to how hot the engine is, you really need to see the actual values coming from the computer.
  10. Thread: Squeaky Leaves

    by JPaul
    Replies
    15
    Views
    445

    WD-40 doesn't last. I don't even buy the stuff...

    WD-40 doesn't last. I don't even buy the stuff anymore, I use PB-Blaster instead for rusted parts since it works better. Use an actual lubricating oil or silicone lube for longer effect. Lanolin...
  11. Replies
    6
    Views
    267

    Should be able to. Probably will need to remove...

    Should be able to. Probably will need to remove the wheel well liners at least though, but those are just plastic rivets. A flathead screwdriver and a body panel prybar are sufficient to take them...
  12. Replies
    6
    Views
    267

    So that you know, that picture doesn't show it...

    So that you know, that picture doesn't show it but the two bolts on the right are directly behind the brace you can see. You have a couple options. Use a spanner/wrench (either standard or...
  13. Thread: Tiger's Build

    by JPaul
    Replies
    13
    Views
    521

    I'm with you. For the amount of work involved in...

    I'm with you. For the amount of work involved in modifying the headlamps and getting them all setup correctly, you might as well just buy some auxiliary lights and rely more on those instead. The led...
  14. Well, it wasn't the blower motor. Got the new one...

    Well, it wasn't the blower motor. Got the new one and plugged it in to make sure I was right, and I wasn't. Spent two hours digging into the wiring and figured out there was a low resistance short to...
  15. Amrg, Electrical is always a pain, even to those...

    Amrg, Electrical is always a pain, even to those of use that do understand it.

    Obviously my problem is that when I rebuilt the engine I upset the delicate balance of the wiring harness so now...
  16. Just go drive behind a dump truck for a bit, then...

    Just go drive behind a dump truck for a bit, then get your insurance to cover the replacement (at least that's what everyone tells me, I have never had an insurance company that covers glass...
  17. Pretty sure I checked recalls on this Alpha and...

    Pretty sure I checked recalls on this Alpha and there were not any outstanding ones. I went through the testing outlined in the service manual and everything checked out, so it's most likely the...
  18. So another project I am probably going to do when...

    So another project I am probably going to do when I can get some downtime for the Alpha is re-wrap the entire engine harness. I'm betting my crank sensor is a similar but far more intermittent issue....
  19. Amrg wins the prize. Decided to take a look at...

    Amrg wins the prize. Decided to take a look at the engine wiring harness before leaving work, you know, wiggle it around and see if anything comes to mind. Lo and behold I put my hand on the section...
  20. I watched it more closely last night. I am...

    I watched it more closely last night. I am definitely keeping pressure based on the MaxTow gauge. At one point I had about 50psi on the MaxTow while the computer thought it was seeing 0.00 psi. Oddly...
  21. Electrical and other gremlins (oil pressure, crank sensor, blower motor)

    So I'm having fun. We've been trying to sell our house and move to far north Utah but of course that hasn't happened yet. I was hoping to have moved by now so that I could park my truck for a bit and...
  22. Replies
    159
    Views
    11,831

    Ha, yeah that was awesome. I saw you pass me and...

    Ha, yeah that was awesome. I saw you pass me and first noticed the mesh doors and then saw the H4O sticker and was like "Oh! I know that guy!"

    I don't have any lift, but I am a bit light in the...
  23. Replies
    159
    Views
    11,831

    Well, thought I'd add an update of sorts. Been...

    Well, thought I'd add an update of sorts. Been working on selling our house so that we can move farther north and get out of the city, but the market for our area apparently slowed to a crawl right...
  24. Replies
    548
    Views
    93,556

    You'll be about 4.5 hours away from me after I...

    You'll be about 4.5 hours away from me after I move up to Cache Valley, UT hopefully before the end of this year (if we can ever sell our house, market is slowed down a lot for me). It'd be great to...
  25. Sexy

    Sexy
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Logout