Welcome to the H4O - HUMMER 4x4 Off Road.

Search:

Type: Posts; User: JPaul

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 33 minute(s) ago.

  1. I know the H3 is 190 ft lbs, so 220 for a bigger...

    I know the H3 is 190 ft lbs, so 220 for a bigger rig doesn't seem far off. But 173 isn't far either, thought a bit low I would think.

    Sent from my SM-N975U using Tapatalk
  2. Thread: V8 oil leak...

    by JPaul
    Replies
    36
    Views
    816

    If you go this route then what I would try is not...

    If you go this route then what I would try is not driving it anywhere but simply start it up and run it for a minute then shut down the engine and check with the UV light. You'll have a better chance...
  3. Thread: V8 oil leak...

    by JPaul
    Replies
    36
    Views
    816

    If it's not the sensor and the rear main seal...

    If it's not the sensor and the rear main seal itself looks ok, then it's either the oil pan (which I think you said was loose?) or the rear cover (seals the whole back of the block from the top of...
  4. Replies
    21
    Views
    1,071

    They haven't been manufactured in probably almost...

    They haven't been manufactured in probably almost a decade if not longer. You'll have to find them used on EBay, classifieds, or forum posts for sale, and they won't be cheap by any stretch of the...
  5. It actually looks like a cheap bushing that is...

    It actually looks like a cheap bushing that is probably undersized or someone wallowed out the bushing hole in the frame. Most likely the bushing is undersized. It is supposed to be an interference...
  6. Thread: V8 oil leak...

    by JPaul
    Replies
    36
    Views
    816

    It doesn't need RTV, the oring is supposed to...

    It doesn't need RTV, the oring is supposed to provide sufficient sealing, provided it is tight. If the oring does not have a sufficient seal it will leak as oil is splashed on it.

    How do the...
  7. Thread: V8 oil leak...

    by JPaul
    Replies
    36
    Views
    816

    If it does it again I would double check the...

    If it does it again I would double check the orings to make sure they didn't get nicked or anything, and make sure that you get a good amount of resistance when inserting the sensor to indicate a...
  8. Thread: V8 oil leak...

    by JPaul
    Replies
    36
    Views
    816

    New sensor or the old one? Looks like mine did...

    New sensor or the old one? Looks like mine did when the oring hardened.

    Sent from my SM-N975U using Tapatalk
  9. Thread: V8 oil leak...

    by JPaul
    Replies
    36
    Views
    816

    The crank sensor was my issue. When I rebuilt the...

    The crank sensor was my issue. When I rebuilt the engine I used all new AC Delco sensors. Ended up with a really bad crank sensor, not only did the O-ring harden and start leaking, but the sensor...
  10. Does your H3 already have the rear view camera? ...

    Does your H3 already have the rear view camera?

    Sent from my SM-N975U using Tapatalk
  11. Thread: Dash Cam Setups

    by JPaul
    Replies
    3
    Views
    132

    I have the Yi dashcam, two of them in fact One...

    I have the Yi dashcam, two of them in fact
    One in the front and one in the rear. People are total liars.

    The front one I have had for over 3 years, the rear one over 2 years. No problems at all...
  12. I'll probably have to wait the ten years or so...

    I'll probably have to wait the ten years or so when these are available used for a decent price, but it definitely has my eye now over a Wrangler for a toy.

    Sent from my SM-N975U using Tapatalk
  13. Yes, I have gone over the wiring schematics in...

    Yes, I have gone over the wiring schematics in detail on the H3's and there are some big differences between the options. I've looked at several options on my base H3 I used to have and found no...
  14. One would like to think they use the same wiring...

    One would like to think they use the same wiring harness regardless of options, but really the answer to that is a hard no. Even more so with the Monsoon vs standard stereo, the wiring for the...
  15. Thread: Roof markers $1K

    by JPaul
    Replies
    15
    Views
    1,111

    Down to $700, just found the listing again when...

    Down to $700, just found the listing again when searching around.

    Sent from my SM-N975U using Tapatalk
  16. Replies
    2
    Views
    177

    Customized H1 "Alpha"

    2001 Hummer H1 Slant Back With Alpha Interior http://www.ksl.com/classifieds/listing/60383228

    I'm not sure how I feel about this one.

    Sent from my SM-N975U using Tapatalk
  17. Replies
    6
    Views
    272

    H3 Using a hi-lift jack is sketchy no matter where...

    Using a hi-lift jack is sketchy no matter where you use it, you easily can have the rig shift or slide on you if you're not careful and lucky.

    If everything is stable and the tires not being...
  18. Thread: LED/Radio Issue

    by JPaul
    Replies
    8
    Views
    626

    I did not have that problem. You do have to make...

    I did not have that problem. You do have to make certain the bulbs are going in the right way, it is possible to install them upside down which would affect that. They have a collar that is locked in...
  19. 200k on the bearings, right? Definitely replace...

    200k on the bearings, right? Definitely replace them since you have it out anyway. The locker itself looks like it was never used so that is good. But the bearings will have worn enough by this point...
  20. Replies
    2,899
    Views
    362,399

    Congrats!! Sent from my SM-N975U using Tapatalk

    Congrats!!

    Sent from my SM-N975U using Tapatalk
  21. The axle seals on the diff will wear out over...

    The axle seals on the diff will wear out over time. They are cheap to replace but make sure the axle stubs aren't grooved/pitted where the seal rides or they'll just start leaking again soon. You can...
  22. Replies
    2,899
    Views
    362,399

    Interesting idea. How is the clearance between...

    Interesting idea. How is the clearance between the lower arm and the axle when fully compressed? You do lose some front clearance though with that drop. Are you going to get new skids made for it so...
  23. Replies
    2
    Views
    127

    Just the arm or do you want to remove the...

    Just the arm or do you want to remove the mechanism too? The arm is easy, remove the spare tire and lift the cap covering the base of the arm to expose the nut. Use a wrench or socket (13mm I think,...
  24. Highly doubtful, I'd just spend the extra 10...

    Highly doubtful, I'd just spend the extra 10 minutes removing the brushguard rather than risk breaking or damaging a $300 part.

    Sent from my SM-N975U using Tapatalk
  25. Replies
    2
    Views
    169

    Yes, I think it's called "paying someone else to...

    Yes, I think it's called "paying someone else to do it."

    I can't recall if I replaced my parking brake shoes when I replaced the pads, I don't think I did.

    Sent from my SM-N975U using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Logout