Welcome to the H4O - HUMMER 4x4 Off Road.

Search:

Type: Posts; User: 4speedfunk

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    8
    Views
    326

    Damn shame the GM units are all gone. One...

    Damn shame the GM units are all gone.

    One thing I suggest, is to measure the length you need and shop around for mass-produced sliders to fit a JK, JL, FJ-Cruiser, Tacoma, etc. You might find...
  2. Replies
    8
    Views
    326

    N-fab

    N-fab
  3. Replies
    0
    Views
    237

    WTS Fresh Alpha SAS build for sale…

    Just finished a SAS/SOA build on a 2008 Alpha. The owner asked me to put the word out that he is wanting to sell (needs funds for a home down payment).

    The build has 5:13s, no lockers, no ram...
  4. Replies
    6
    Views
    1,658

    Well I finally did it. I bought some RIVN...

    Well I finally did it. I bought some RIVN today…$44/share. Gonna sit back for a couple years and see if they can actually produce a truck that lives up to the net-hype.

    Bought some FSR too.
  5. Replies
    295
    Views
    186,445

    Cg…how did the drilling go? Some aftermarket...

    Cg…how did the drilling go?

    Some aftermarket shafts are so hard they cannot be touched by a hand drill/bit.
  6. Replies
    295
    Views
    186,445

    .025” wire? Sent from my iPhone using...

    .025” wire?


    Sent from my iPhone using Tapatalk
  7. Replies
    15
    Views
    3,079

    A solid front axle swap will allow lower gearing....

    A solid front axle swap will allow lower gearing. The stock rear axle can be re-geared without issue. I commonly install 4.88 and 5.13 gears and this setup works well with 37” tires. Cruises...
  8. Replies
    9
    Views
    785

    WTS 2008 IFS part out

    This SAS/SOA build is nearly complete. Back on the ground and getting the final details hashed-out...

    https://uploads.tapatalk-cdn.com/20220205/25a3f5884461ecbed6251bb36e2f78f1.jpg

    Still got a...
  9. Replies
    9
    Views
    284

    H3 Maybe it’s not the pass key system? My H3 will...

    Maybe it’s not the pass key system? My H3 will lock the key in the ignition anytime the battery gets low. Sometimes it sits for a couple months and when I try to start it…it freaks out and locks...
  10. Replies
    15
    Views
    546

    You rotated the ignition key to “on” during...

    You rotated the ignition key to “on” during bleeding, correct?
  11. Replies
    8
    Views
    344

    Service stab sys - tire problem?

    I think it would take a larger differential in tire size to throw a Stabilitrac light. Even if the difference in tire size was enough to activate Stabilitrac, it would not throw a light. It would...
  12. Replies
    7
    Views
    310

    Make sure the new rack isn’t slipping back &...

    Make sure the new rack isn’t slipping back & forth during turning. There is a clamp on the passenger side and two bushings on the drivers side…both are often overlooked but, they can cause the...
  13. Replies
    55
    Views
    1,452

    H3 Hub puller. Most AutoZone stores will loan or...

    Hub puller. Most AutoZone stores will loan or rent one. It’s basically a giant slide hammer that attaches to the wheel studs.
  14. Replies
    20
    Views
    902

    You might try hitting some Colorado-Canyon...

    You might try hitting some Colorado-Canyon forums. Same drivetrain but, larger audience. Low mileage GM five bangers are very hard to find. They are very expensive and difficult to do internal...
  15. I don’t get it. I looked at the eBay...

    I don’t get it. I looked at the eBay listing…read the description…still couldn’t figure out what it is.
  16. Does anyone know how to remove these crossbars...

    Does anyone know how to remove these crossbars without a key?

    I am doing a SAS on an H3 right now, and I may have to remove these to get it out thru the doorway…...
  17. Might look around for Colorado/Canyon offerings...

    Might look around for Colorado/Canyon offerings too. That way you can get extras (C/Cs have four bushings).

    If all else fails, make your own. Years ago (before OD was around), I used some...
  18. Replies
    6
    Views
    446

    https://indianapolis.craigslist.org/pts/d/north-ve...

    https://indianapolis.craigslist.org/pts/d/north-vernon-x4-h3-hummer-37l/7419297267.html
  19. Replies
    3
    Views
    205

    Wear.

    Wear.
  20. Replies
    3
    Views
    205

    I had that same thing happen on my 98 S10 years...

    I had that same thing happen on my 98 S10 years ago. It was the clutch itself. The pressure plate springs suddenly let go. No funny noises or anything…just hardly any pedal.
  21. Replies
    4
    Views
    507

    14-bolt rear axle swap…

    Duelly axle from a 2006 2500HD…
    https://uploads.tapatalk-cdn.com/20220105/ea692dfa5d93aaa57d96ea591f371320.jpg
    https://uploads.tapatalk-cdn.com/20220105/6530acfb17ad3ef49d14d33a3ed8534f.jpg
  22. Replies
    9
    Views
    785

    WTS 2008 IFS part out

    Your torsion bars are fine. You just got em indexed wrong (see the novel I left in your “lift” thread).

    I guess the correct term for plasti-dipped step bars would be: #trans.

    Not that...
  23. Replies
    28
    Views
    1,659

    Your torsion issue is real common. It’s more...

    Your torsion issue is real common. It’s more likely due to the Rancho extension castings being flipped…and not due to “worn” t-bars. I have messed with quite a few of these, and although the Rancho...
  24. Replies
    9
    Views
    785

    WTS 2008 IFS part out

    The usual…SAS project. This is one is a 08 Alpha lux/non Adv Pak w/90k. Parts available:

    -c.I. front diff (4.10-single track) $650
    -Alpha torsion bars SOLD
    -Fox front shocks (500 miles) SOLD...
  25. Replies
    9
    Views
    1,174

    I use that stuff for my Christmas tree lights.

    I use that stuff for my Christmas tree lights.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Logout