Welcome to the H4O - HUMMER 4x4 Off Road.

Search:

Type: Posts; User: JPaul

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. H3 The reason for the difference between the...

    The reason for the difference between the Wrangler and the H3 is due to wheelbase, as well as engine size. The longer wheelbase provides a more stable tow vehicle so it can handle pulling heavier...
  2. Replies
    9
    Views
    91

    Both. Sent from my SM-N975U using Tapatalk

    Both.

    Sent from my SM-N975U using Tapatalk
  3. Replies
    16
    Views
    317

    H3 Pretty sure the thermostat should never be on the...

    Pretty sure the thermostat should never be on the inlet side since it's not going to really cool the engine. If it is on the inlet side then the moment the cooler fluid flows past it the thermostat...
  4. Replies
    16
    Views
    317

    H3 My understanding is they went to the higher...

    My understanding is they went to the higher opening temperature for emissions, the cooler temp was keeping the engine from operating at a more effective temperature when not being pushed very hard...
  5. Replies
    15
    Views
    1,634

    Is there a part number or anything for that strut...

    Is there a part number or anything for that strut or can you just search for any FJ cruiser rear door strut?

    Congrats on finishing your degree!
  6. Replies
    15
    Views
    1,634

    Seems like it should be grounded, but checking...

    Seems like it should be grounded, but checking the FSM schematics I don't see one. One task I have for when I can get around to installing my ham radio is to do a full bonding of all the body parts...
  7. Replies
    10
    Views
    181

    I can measure the ohms on mine when I get home,...

    I can measure the ohms on mine when I get home, but that looks like an overcurrent where it drew enough amps to melt the insulation but not enough to trip the fuse or breaker on the sPod.

    Sent...
  8. Thread: H3 locking hubs

    by JPaul
    Replies
    8
    Views
    224

    I'm curious as to what broke exactly and what the...

    I'm curious as to what broke exactly and what the scenario was when they broke.

    Sent from my SM-N975U using Tapatalk
  9. I stand corrected. Looks like plastic in all the...

    I stand corrected. Looks like plastic in all the pictures I have seen, but stamped or cast metal is only marginally better I think.

    Yeah, neither is going to stop a deer, you need a proper bullbar...
  10. Thread: MTUH3 Build

    by JPaul
    Replies
    21
    Views
    3,818

    I hate to tell you this, but those are holes, not...

    I hate to tell you this, but those are holes, not dents. And now you have me terrified of what I might find if I ever get around to pulling my rocker covers off... :whaa:
  11. Acer does great videos. Good for all the new...

    Acer does great videos. Good for all the new owners figuring out these are actually really fun rigs to own and drive.
  12. Thread: H3 locking hubs

    by JPaul
    Replies
    8
    Views
    224

    26243

    26243
  13. Thread: H3 locking hubs

    by JPaul
    Replies
    8
    Views
    224

    Have you guys been under a rock? Big long...

    Have you guys been under a rock? Big long misinformed thread about this thing a few months back, amrg linked it above.
  14. You mean the useless plastic one? I never...

    You mean the useless plastic one? I never understood the point of that one.
  15. Looking good! Maybe this coming winter I'll have...

    Looking good! Maybe this coming winter I'll have time to start working on my layout. The new house and land is keeping me too busy to do anything with my trains. Might try setting up the G scale...
  16. Replies
    11
    Views
    310

    H3 Hopefully the brackets bend before the tank does,...

    Hopefully the brackets bend before the tank does, but you'd have to really be in the rocks for that to happen if you've mounted the tank inside the rails. The rock rails on the other hand are...
  17. Replies
    11
    Views
    310

    H3 Not sure I'd want something meant to be hit by...

    Not sure I'd want something meant to be hit by big rocks to be pressurized. That could end very badly.
  18. Replies
    9
    Views
    240

    Delrin is pretty cheap really, especially some...

    Delrin is pretty cheap really, especially some 1/8" thick scrap pieces which is all you'll need. It's easy to work with as well, wood saws and drills can cut it no problem. Probably just look up...
  19. Replies
    11
    Views
    310

    H3 That's the same place I have planned for my 2.5...

    That's the same place I have planned for my 2.5 VIAR gallon tank, though I might end up trying to replace the resonator and muffler with a single Dynaflow Ultraflow Stainless Steel muffler in the...
  20. Replies
    9
    Views
    240

    Seems like a unicorn part, what are they made of?...

    Seems like a unicorn part, what are they made of?

    Sent from my SM-N975U using Tapatalk
  21. $24,000, slightly used. No lowballers, I know...

    $24,000, slightly used. No lowballers, I know what I've got.
  22. Replies
    4
    Views
    387

    With a cursory glance I see that the link to the...

    With a cursory glance I see that the link to the Garage is HTTP instead of HTTPS and when you follow it you're not logged in. However I remain logged in if I go back to the forums. Also, if you...
  23. Replies
    18
    Views
    583

    Did you try unplugging it and plugging it back in...

    Did you try unplugging it and plugging it back in again? Might be a bad contact or something. Also check any other connections back there that might have come undone or anything.

    Sent from my...
  24. Replies
    2,822
    Views
    346,015

    How's the running noise with it in the door?

    How's the running noise with it in the door?
  25. Replies
    28
    Views
    1,253

    I have some N95 masks but they were from when I...

    I have some N95 masks but they were from when I was doing CERT (Community Emergency Response Team) and I mainly used them around the house for working on stuff like grinding or in the attic or crawl...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Logout