Welcome to the H4O - HUMMER 4x4 Off Road.

Search:

Type: Posts; User: JPaul

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    6
    Views
    184

    Should be able to. Probably will need to remove...

    Should be able to. Probably will need to remove the wheel well liners at least though, but those are just plastic rivets. A flathead screwdriver and a body panel prybar are sufficient to take them...
  2. Replies
    6
    Views
    184

    So that you know, that picture doesn't show it...

    So that you know, that picture doesn't show it but the two bolts on the right are directly behind the brace you can see. You have a couple options. Use a spanner/wrench (either standard or...
  3. Thread: Tiger's Build

    by JPaul
    Replies
    6
    Views
    169

    I'm with you. For the amount of work involved in...

    I'm with you. For the amount of work involved in modifying the headlamps and getting them all setup correctly, you might as well just buy some auxiliary lights and rely more on those instead. The led...
  4. Well, it wasn't the blower motor. Got the new one...

    Well, it wasn't the blower motor. Got the new one and plugged it in to make sure I was right, and I wasn't. Spent two hours digging into the wiring and figured out there was a low resistance short to...
  5. Amrg, Electrical is always a pain, even to those...

    Amrg, Electrical is always a pain, even to those of use that do understand it.

    Obviously my problem is that when I rebuilt the engine I upset the delicate balance of the wiring harness so now...
  6. Just go drive behind a dump truck for a bit, then...

    Just go drive behind a dump truck for a bit, then get your insurance to cover the replacement (at least that's what everyone tells me, I have never had an insurance company that covers glass...
  7. Pretty sure I checked recalls on this Alpha and...

    Pretty sure I checked recalls on this Alpha and there were not any outstanding ones. I went through the testing outlined in the service manual and everything checked out, so it's most likely the...
  8. So another project I am probably going to do when...

    So another project I am probably going to do when I can get some downtime for the Alpha is re-wrap the entire engine harness. I'm betting my crank sensor is a similar but far more intermittent issue....
  9. Amrg wins the prize. Decided to take a look at...

    Amrg wins the prize. Decided to take a look at the engine wiring harness before leaving work, you know, wiggle it around and see if anything comes to mind. Lo and behold I put my hand on the section...
  10. I watched it more closely last night. I am...

    I watched it more closely last night. I am definitely keeping pressure based on the MaxTow gauge. At one point I had about 50psi on the MaxTow while the computer thought it was seeing 0.00 psi. Oddly...
  11. Electrical and other gremlins (oil pressure, crank sensor, blower motor)

    So I'm having fun. We've been trying to sell our house and move to far north Utah but of course that hasn't happened yet. I was hoping to have moved by now so that I could park my truck for a bit and...
  12. Replies
    159
    Views
    11,490

    Ha, yeah that was awesome. I saw you pass me and...

    Ha, yeah that was awesome. I saw you pass me and first noticed the mesh doors and then saw the H4O sticker and was like "Oh! I know that guy!"

    I don't have any lift, but I am a bit light in the...
  13. Replies
    159
    Views
    11,490

    Well, thought I'd add an update of sorts. Been...

    Well, thought I'd add an update of sorts. Been working on selling our house so that we can move farther north and get out of the city, but the market for our area apparently slowed to a crawl right...
  14. Replies
    545
    Views
    91,985

    You'll be about 4.5 hours away from me after I...

    You'll be about 4.5 hours away from me after I move up to Cache Valley, UT hopefully before the end of this year (if we can ever sell our house, market is slowed down a lot for me). It'd be great to...
  15. Sexy

    Sexy
  16. If you're only getting 30k then you're either...

    If you're only getting 30k then you're either using cheap garbage, you're driving too fast every where and constantly braking too hard, you're only replacing the pads and none of the hardware so the...
  17. Thread: Salvage H3T

    by JPaul
    Replies
    25
    Views
    1,023

    H3T bed on a M101A(x) frame. Not sure how common...

    H3T bed on a M101A(x) frame. Not sure how common my situation is, but I think you can find a M101A1 or the like with a trashed tub but good frame for pretty inexpensive. My M101A1 (might be an A2)...
  18. Replies
    4
    Views
    440

    Yoink! JK. Working on buying a new place...

    Yoink!

    JK. Working on buying a new place farther north and selling the current house right now. Wife would kill me if I picked up an axle to sit around while the front pumpkin is still at the shop...
  19. Replies
    7
    Views
    434

    Use a mechanics stethoscope and listen to it....

    Use a mechanics stethoscope and listen to it. Could still be an exhaust leak. I had a rod bearing go at 85k on my 3.7, aftermarket warranty covered it since everything else checked out fine when the...
  20. It probably works just fine, you have good...

    It probably works just fine, you have good support front and rear so it's not just the roof taking all the weight, plus I highly doubt this guy was bouncing around offroad with that setup. Probably...
  21. If he has to ask if there is a way to modify his...

    If he has to ask if there is a way to modify his fuel system on a high pressure injection system, he shouldn't be doing it period. Yeah, he can do what he wants, but don't encourage him when it's not...
  22. You could put an inline filter in if you are...

    You could put an inline filter in if you are willing to risk fuel leaks, fires, or other mishaps when it's improperly installed in a high pressure fuel injected system. Gas in the US at least is...
  23. Replies
    12
    Views
    499

    My 2008 has them on either side of the block. I...

    My 2008 has them on either side of the block. I think they moved them there for AFM.

    Sent from my SM-N950U using Tapatalk
  24. Replies
    34
    Views
    5,262

    H3T Need a shovel for this thread? [emoji38] Odds...

    Need a shovel for this thread? [emoji38]

    Odds are the transmission was fixed/replaced.

    Sent from my SM-N950U using Tapatalk
  25. Replies
    159
    Views
    11,490

    atvspeed aka Outfitter Design is going to be...

    atvspeed aka Outfitter Design is going to be coming out with it. I wasn't specific because I mirror this thread on a couple other forums and just copy/paste my main posts.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Logout