Welcome to the H4O - HUMMER 4x4 Off Road.

Search:

Type: Posts; User: atvspeed4

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. This should be interesting we have tested 3d...

    This should be interesting we have tested 3d printed parts for production and its not there yet for durability when used outside the vehicle from our research. We were working our own adapters prior...
  2. Replies
    17
    Views
    333

    H3 You could have a HD built 6l80 installed for half...

    You could have a HD built 6l80 installed for half the price of getting a 6l90 to work where it will feel and be factory correct. Just make sure they do the wiring and programming right. Most of the...
  3. Replies
    17
    Views
    333

    H3 Yup.

    Yup.
  4. Replies
    17
    Views
    333

    H3 Go with the 6l80 much easier swap especially...

    Go with the 6l80 much easier swap especially since it's 32 spline. When we measured it, the 6l80 was about 1/4" longer which works perfectly. The 6l90 was about 1.6" if I remember which does not...
  5. Replies
    17
    Views
    333

    H3 I believe we are the only ones to have...

    I believe we are the only ones to have successfully done a 6l90 swap and it wasn't fun. Good luck [emoji106]
  6. Replies
    17
    Views
    333

    H3 Exactly, we did the swap you listed and you...

    Exactly, we did the swap you listed and you cannot run the factory t case due to the overall length and torsion bar crossmember. 6l90 output shaft cannot safely be turned down to 27 spline due to...
  7. Replies
    9
    Views
    251

    Sorry to hear that! I feel ya same thing happened...

    Sorry to hear that! I feel ya same thing happened to me with an angle grinder. Was in rush and disk jammed in piece then jumped out and grabbed my finger. Took a long time for all the little pieces...
  8. Thread: broken leaf?

    by atvspeed4
    Replies
    41
    Views
    3,885

    The sleeve is not supposed to rotate within the...

    The sleeve is not supposed to rotate within the hanger most even have small teeth that bite into hanger to stop them from rotating. All rotation is supposed to be in the rubber just like the IFS...
  9. Thread: broken leaf?

    by atvspeed4
    Replies
    41
    Views
    3,885

    I originally thought back in 2014 that it must be...

    I originally thought back in 2014 that it must be rust but after looking at each of the breaks there is no sign of rust at that spot other than usual light surface corrosion on whole leaf pack . This...
  10. Thread: broken leaf?

    by atvspeed4
    Replies
    41
    Views
    3,885

    I know its an old post but following up we just...

    I know its an old post but following up we just had another main leaf break in the same spot on our alpha. This is the 4th h3 we have had this happen to since my post in this thread. All in the same...
  11. Replies
    22
    Views
    868

    Spoke to the shop that assembled the prototypes...

    Spoke to the shop that assembled the prototypes and they are currently 8 weeks out for any new orders. We are happy to order ahead of time but with so many options for lockers/ limited slips and gear...
  12. Replies
    16
    Views
    718

    I've had a 2wd transfer case in our 6.0L swapped...

    I've had a 2wd transfer case in our 6.0L swapped h3 I hate not having the AWD anymore.
  13. Replies
    12
    Views
    726

    We have been filling a large wait-list for the...

    We have been filling a large wait-list for the past month but are finally caught up. Next batch is hopefully going to be done this Friday and we can ship out Saturday. Feel free to shoot us an email...
  14. Replies
    21
    Views
    2,284

    The old link I had saved is dead but when they...

    The old link I had saved is dead but when they switched to 3.7l in 2007 they went to 280mm even in h3. They are interchangeable from what I have read so I'd just get the 280mm and be done since you...
  15. Replies
    22
    Views
    868

    We haven't designed a setup compatible with the...

    We haven't designed a setup compatible with the rancho yet. The stronger pinion mount we use goes under the crossmember so it does not rely on the bolt in tension when you load the diff. We had a...
  16. Replies
    22
    Views
    868

    No updates really, still cant find a smaller Cv...

    No updates really, still cant find a smaller Cv shaft that will clear slightly rubbing the lower control arm at full compression. We have had this diff installed in a h3T that has been driven over...
  17. Replies
    21
    Views
    2,284

    I believe in 2008 they increased the size of the...

    I believe in 2008 they increased the size of the clutch
  18. Thread: Rancho Kit

    by atvspeed4
    Replies
    5
    Views
    387

    Craigslist This is almost making me want to sell our new in...

    This is almost making me want to sell our new in box complete kit but I feel like as soon as we do we will have a project truck we want to put it on.
  19. Replies
    23
    Views
    1,025

    We were getting a similar smell it ended up being...

    We were getting a similar smell it ended up being a bad radiator cap which was showing no signs of leaking but once replaced off of a suggestion from a friend solved the problem. Definitely go Ac...
  20. Replies
    30
    Views
    2,264

    H3 No go lower shock mount style and position...

    No go lower shock mount style and position different. Also, zr2 has same wheel travel as h3 no gains
  21. Replies
    21
    Views
    907

    I remember a few years ago reading about a...

    I remember a few years ago reading about a Colorado guy doing a rebuild and looking into how they remove the cylinder sleeves for when he was doing a rebuild I guess they were fine and he just honed...
  22. Replies
    167
    Views
    34,846

    Those are going to be our next tires for sure....

    Those are going to be our next tires for sure. How bad is the ride with them being bias ply?
  23. We replaced the upper on one of our trucks and it...

    We replaced the upper on one of our trucks and it was shot again after driving cross country and wheeling Moab for a week. Wish there was a better upgrade
  24. Replies
    2
    Views
    210

    They were talking about it on another forum its...

    They were talking about it on another forum its hilarious how close it matches the H2. One of the police versions I saw in black is almost spot on to an H2
  25. Awesome video! We wish we had more time to put...

    Awesome video! We wish we had more time to put out great how to content like this
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Logout