Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Welcome to H4O! For a reduced ad experience, please login or register with the forum.
Forums
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
A
atvspeed4
Well-Known Member
·
From
massachusetts
Joined
Sep 12, 2011
Last seen
Wednesday at 10:17 AM
Messages
1,173
Reaction score
340
Points
83
Find
Find content
Find all content by atvspeed4
Find all threads by atvspeed4
Latest activity
Postings
About
A
atvspeed4
replied to the thread
Hummer H3 HD Dana 50/ CV shaft upgrade
.
The only failures we have had over the years were the inner tripod style joint cracking the outer housing when fully extended. This...
Mar 19, 2024
A
atvspeed4
replied to the thread
Hummer H3 HD Dana 50/ CV shaft upgrade
.
Well it was finally a success! No leaks and the new HD plunging CVs fit. At full lock and full compression with the bump stop slammed...
Mar 19, 2024
A
atvspeed4
reacted to
Clark's post
in the thread
H3
Back door
with
Like
.
Do you mean this one? "I hope" lol
Feb 29, 2024
A
atvspeed4
replied to the thread
H3
Back door
.
No its the other side on the door that does not have rubber that you squeeze in vise so it grabs what you have in the picture tighter
Feb 26, 2024
A
atvspeed4
replied to the thread
Hummer H3 HD Dana 50/ CV shaft upgrade
.
Well little delay as our HD driveshaft we did not grease the slip joint so it rusted solid totally our fault and was not able to be...
Feb 20, 2024
A
atvspeed4
replied to the thread
H3
Back door
.
Definitely give the strike a squeeze in a vise and you'll be good to go for a long time.
Feb 16, 2024
A
atvspeed4
replied to the thread
H3
Back door
.
Take the strike plate off and gently squeeze in a vice then reinstall. Its a common thing especially with 37 tire mounted as spare. It...
Feb 15, 2024
A
atvspeed4
replied to the thread
Replacing vs Rebuilding 5.3 in Alpha
.
You just need to make sure that whatever Gen 4 engine you get has "car" style motor mount holes on the block. The alpha uses those not...
Feb 8, 2024
A
atvspeed4
reacted to
H3TONKA's post
in the thread
Hummer H3 HD Dana 50/ CV shaft upgrade
with
Like
.
Best of luck with this next test run, hopefully it's the last one. We all have our fingers crossed that you guys have finally nailed it...
Feb 7, 2024
A
atvspeed4
replied to the thread
Hummer H3 HD Dana 50/ CV shaft upgrade
.
Good news, they think it wasn't a huge issue. It appears that since this specific one has been our prototype housing for near 8 years...
Feb 6, 2024
A
atvspeed4
replied to the thread
Frame swap on a 08 h3 alpha
.
There are a few changes but biggest would just be getting motor mount adapters like the ones current performance sells.
Jan 29, 2024
A
atvspeed4
replied to the thread
Hummer H3 HD Dana 50/ CV shaft upgrade
.
Still kicking. Dropped the truck off 3 weeks ago to see why seals were leaking AGAIN. They said it appears diff was overfilled despite...
Jan 22, 2024
A
atvspeed4
replied to the thread
Front CV axle upgrade?
.
Not the right length
Jan 18, 2024
Loading…
Loading…
Forums
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top