Wolf H3

H3Wolf · Nov 28, 2016

Looking at buying a brush guard for my next mod.

Sent from my SM-G920V using Tapatalk

??? · Dec 18, 2016

Can you post more info on your cb setup?

H3Wolf · Jan 18, 2017

??? said:
Can you post more info on your cb setup?

It's a Cobra Ultra 19 III cb, don't remember brand of coax cable. Made a spare tire bracket to hold the firestick. The ground is ran straight to the nearest ground spot, and the power is ran and connected to the battery. I'll post pictures tomorrow.

Sent from my SM-G920V using Tapatalk

H3Wolf · Jan 18, 2017

Started and finished my cargo box, shovel mount and my tray table, today. Along with unclogging all the drain tubes on Otxoa, meant to do everything in a couple hours but the drain tubes are a lot harder with just one person. But here are the pics.

H3Wolf · Jan 18, 2017

So far it's holding

Kyle · Jan 19, 2017

What did you do with your H3X brush guard, I noticed its not on. wanna sell it? Im looking for one.

H3Wolf · Jan 19, 2017

Sorry already sold it.

H3Wolf · Feb 8, 2017

??? said:
Can you post more info on your cb setup?

This is basically what I did. But don't do it, cause I'm having cralossed signalling issues still, and I'm trying to figure out why

Sent from my SM-G920V using Tapatalk

JPaul · Feb 8, 2017

You need to wire the cb directly to the battery, anything else and you're going to get noise issues. You shouldn't even need the noise filter unless something is wrong in the engine bay.

Sent from my SM-N910T using Tapatalk

JPaul · Feb 8, 2017

That includes running both the positive AND the negative directly to the battery terminals btw. Don't run your negative to a ground point, it doesn't seem like it would but it does make a difference.

Sent from my SM-N910T using Tapatalk

deserth3 · Feb 9, 2017

Your wiring looks fine. I think your problem is most likely where you physically are running the wires.
You have to stay away from the master brake cylinder. It has a motor that pressures the brake fluid that is notorious for inducing sound onto any wires run near it.
I connect my CB to the back of my power outlets in the dash and haven't had a problem. And I don't use a filter either.

Sent from my Moto G (4) using Tapatalk

H3Wolf · Feb 11, 2017

deserth3 said:
Your wiring looks fine. I think your problem is most likely where you physically are running the wires.
You have to stay away from the master brake cylinder. It has a motor that pressures the brake fluid that is notorious for inducing sound onto any wires run near it.
I connect my CB to the back of my power outlets in the dash and haven't had a problem. And I don't use a filter either.

Sent from my Moto G (4) using Tapatalk

That's exactly what it's connected to.

Sent from my SM-G920V using Tapatalk

H3Wolf · Feb 12, 2017

Had the issue with and without the filter. Been connected to the power outlet in my dash.

Sent from my SM-G920V using Tapatalk

H3Wolf · Feb 12, 2017

Did some more stuff over the weekend. Was tired of the brushed steel look on the interior so I wrapped and painted it.

Then I cut the muffler off, sounds perfect for what I want. Put a kill switch to my cb. Also switched all the white lights to the gauges are now red. That right there was a scary experience. But it works

Sent from my SM-G920V using Tapatalk

Kyle · Feb 12, 2017

I like the carbon fiber dash with the radio done. I'm going to do that next

Sent from my iPhone using Tapatalk

scoreh3 · Feb 12, 2017

That looks really nice !

H3Wolf · Feb 12, 2017

I had my friend lay it out then I cut everything, had to take the stock radios face plate off.

Sent from my SM-G920V using Tapatalk

H3Wolf · Feb 12, 2017

Here's the gauges with the red lights. [emoji27] out of all the mods this one scared me lol

Sent from my SM-G920V using Tapatalk

Panzer07 · Feb 12, 2017

Is that rune writing I see under the 4x4 controls ?? Hard to make out

Sent from my SM-G930T using Tapatalk

H3Wolf · Feb 12, 2017

Yep

Sent from my SM-G920V using Tapatalk

H3Wolf · Feb 13, 2017

Elder futhark, for control, an for Otxoa.

Sent from my SM-G920V using Tapatalk

Bigunit · Feb 15, 2017

Very cool!

H3Wolf · Feb 16, 2017

I'm very happy with it, now I just got to figure out my melted rear bumper situation, lol. I'm thinking about diamond plate. But seriously Arlock, thanks for the help in my decision making, on cutting my muffler off, it sounds pretty damn good now.

CaddyStrophic · Feb 21, 2017

Your chariot, to Valhalla!!!! Nice job, man.

Sent from my Nexus 6 using Tapatalk

H3Wolf · Feb 22, 2017

Currently I'm making a jerry can carrier for the back door. What I thought was simple and easy turned out to be kinda hard. Needless to say don't try and drill metal with a cordless drill unless you have more then one battery

That's it so far.. thanks alot job for making me work..

Sent from my SM-G920V using Tapatalk

Wolf H3

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Hammer Down!

Well-Known Member

Well-Known Member

Well-Known Member